• Largest stock!
  • More than 15 years of experience!
  • Authorized Brodit dealer!
  • Professional advise!
  • +31 35-6780806
Language
PDAplus English PDAplus English
Toggle Nav Toggle Nav
Search

Menu

Toggle Nav
Close
Brodit holder fixed install. Unitech PA720
Brodit holder fixed install. Unitech PA720
Brodit holder fixed install. Unitech PA720
Brodit holder fixed install. Unitech PA720
Brodit holder fixed install. Unitech PA720

Brodit holder fixed install. Unitech PA720

article number
513981
Not in stock
Be the first to review this product
€101.95
-
+
Add to order list Add to Compare
Details
An active holder which is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior!
 
You can choose to use the holder as an active holder for charging of your device only, or to connect an adapter to the Molex connector for additional features. Then you can use the holder also for power supply of a GPS receiver or other own solutions (can not be used for data communication or audio connection).
 
12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger.  Professional installation recommended.
The holder is equipped with a tilt swivel so you can easily adjust the angle for better viewing, or switch between portrait and landscape mode. Tilts 20° and swivels 360°. Mounting plate 42x50 mm with predrilled AMPS-holes +2x3,5 mm centered holes. Made of high grade black ABS/Acetal plastic. Made in Sweden. Attach onto ProClip Mounting Platform.
 
Dimensions: 87 x 103 x 71 mm (W x H x D mm)
Weight: 233 g
Cable length: Total length: 240 cm (Holder to box: 70 cm, Connectors+box 14 cm, Box to open end: 156 cm.)
 
Charging specifications:
Input voltage: DC/10-30V
Charging voltage: DC/4.75-5.3V
Output current(Typ): 2.0A
Input & output protection: Input polarity reversal/Output over voltage/Output over current/Output short protection
LED charging indicator: Power input indicator(Green), Ovp/Ocp/Output short(Red)
Operating temperature: 0°C ~ +40°C
Storage temperature: -20°C ~ +80°C
RoHS compliant: ROHS
More Information
More Information
Accessory brand Brodit
Barcode 7320285139817
Recommended retail price incl. VAT 101.95
Device holder type PDA holder
Connection Fixed installation
Device holder features Device specific
Color Black
Voltage 12/24V geschikt
Device holder lockable? no
Productinfo Brodit houder
Product installation Mount the holder on a ProClip in your vehicle. A detailed installation manual is included in the product packaging
Product suitable for Brodit houder
Reviews
Write Your Own Review
You're reviewing:Brodit holder fixed install. Unitech PA720
Compatibility
Instruction
Please read all of the instructions and  look at the pictures before attaching the holder. Important Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! Note: If you are connecting a GPS/Data device to the holder please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters.
 
Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis.
2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.
 
How to mount the holder: 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws.
3. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw until the holder is firmly in place, but still can be adjusted.
4. The holder is in place.

Cancel Continue Shopping
Scroll to top